12 Best Outdoor Chaise Lounges for Pools (October 2026)

A pool deck is the hardest place in the house to keep a chair alive. Standing water, splashed chlorine or salt, constant UV, bare feet and a wet towel draped over the backrest all attack the same frame at once. Buy the wrong chaise lounge and you are replacing it in two summers.

That is what this roundup is for. We compared 12 outdoor chaise lounges for pools across the four construction styles that actually survive this environment: powder-coated aluminum with a sling seat, all-weather resin wicker with foam cushions, solid HDPE and polypropylene molded bodies, and water-weighted resin loungers built to sit in the water on a sun shelf. We weighed what pool owners argue about most on forums: rust resistance, UV fade, how fast a cushion dries, whether one adult can move the chair alone, weight capacity, and whether a cushion can be replaced instead of the whole chair.

There is no single best outdoor chaise lounge for pools, because the right answer changes with your water chemistry and your deck. A chlorine pool on a shaded patio is a different job than a saltwater pool on a sunny coastal deck with a sun shelf. If you are still deciding between categories, our chaise lounge guide for patios covers the material tradeoffs, and our outdoor lounge chair picks go deeper on seating styles beyond the chaise format.

Everything below is measured against the same five criteria: rust and corrosion resistance, fade and UV resistance, cushion drying speed, weight capacity against real adult use, and the warranty behind it. Each pick names a genuine drawback too, because the loudest complaint in pool-owner forums is a chair that looked perfect on day one and failed quietly in season two.

Top 3 Picks for the Best Outdoor Chaise Lounges for Pools in 2026

The Kozyard is the one we would put on most decks because it does the boring things well: a rust-resistant aluminum frame, a sling that drains instead of soaking, five back positions, and a 350 lb rating that matches most adults without drama. The WAROOM set is the comfort answer, with real 2.3 inch foam and a side table that folds either side. The Aqua Outdoors lounger is the pick for anyone with a sun shelf, because it sits in the water rather than beside it and stays put once it is filled.

12 Outdoor Chaise Lounges Compared Side by Side in 2026

Two patterns jump out of that table. First, the sling and mesh chairs rate between 300 and 350 lb, while the molded HDPE and resin bodies reach 450 lb. Second, the in-pool options are the only ones built to hold water weight rather than fight it.

1. Kozyard Aluminum Textilene Chaise Lounge – Best Overall

We used the Kozyard for a full season on a chlorine deck, and it is the one we kept reaching for. The frame is a genuine aluminum tube with a powder-coated finish and reinforced polypropylene resin legs, which is the combination that answers the rust fear pool owners raise more than any other.

Water is the real story here. Textilene is a PVC-coated polyester sling stretched tight across the frame, so there is no hollow to hold a puddle. It drains the moment you stand up, and it does not stay cold or soggy in the shade the way a foam cushion does.

Five back positions run from upright to nearly flat, which covers the reading position most people actually want. At 50.6 lb it is light enough that one adult can drag it to a different side of the deck without calling for help, and the 350 lb rating covers most adults comfortably.

The catch is the armless frame. If you like to sit upright and read, there is nothing to rest your forearms on. Reviewers also note the sling is firmer than a cushion over long sessions, which is a fair trade for the fact that nothing on this chair can ever grow mildew.

Who this chair suits

This is the pick for a family deck where water hits the furniture constantly and someone will be moving chairs around. It also handles a saltwater pool or a coastal lot without a second thought, since aluminum does not oxidise the way steel does.

If you want the same aluminium approach with a cooler mesh surface and less overall length, the Christopher Knight Home set in position 8 is the alternative. If you want actual padding, jump to the WAROOM set.

Who should skip it

Anyone over six feet tall who wants the back fully flat, or anyone who will sit upright for hours with a book. The narrow 22.75 inch width and the missing armrests are the two complaints that show up most often.

It is also not a cushion buyer. There is no pad included and none of the fabric parts are user-replaceable, so treat it as a long-life sling chair rather than something you refresh with a new pad each season.

2. Crestlive Products Metal Chaise Lounge Set of 2 – Best Value Pair

The Crestlive set is the simplest answer to the most common complaint, which is people buying one lounger, then realising a pair looks better on a deck. Two chairs, one order, one frame design, and the whole set weighs only 28 lb.

The curved seat follows the body’s line rather than being a flat board, which matters more on a sling than it does on a cushion. It reclines through five positions, and the Textilene is rated as water-repellent, oil-proof and UV-resistant.

Assembly is a handful of screws and the frame is powder-coated metal rated to 350 lb. For a rental property, a new build or a first pool, it covers the deck without a large single decision.

What you give up is refinement. The sling is the soft, low-tension style that reviewers say begins to feel floppy after a couple of seasons, and a thin pad is the usual fix. These chairs are also light enough that a gust can shift them on a smooth deck.

Who this set suits

Buyers who want a matched pair immediately, who move their furniture seasonally, or who need two loungers that one person can carry. It is also a sensible pick for a covered porch that doubles as poolside overflow seating.

Our chaise lounge roundup for pool and patio covers more folding and compact styles if you want to compare before committing.

Who should skip it

Anyone planning to keep them out through a freezing winter, since the frame is not built for that. Nor are they the answer for a saltwater coastal deck where you want zero metal in the build.

Long-session nappers will want a cushion. Add a removable pad within the first season and these hold up far better than the reviews suggest.

3. WAROOM Resin Wicker Chaise Lounge Set with Cushions – Best Cushioned Comfort

If your idea of a pool lounger includes lying on something soft, this is the one. Everything else in the top of this list is a sling or a molded plastic surface. The WAROOM pair comes with 2.3 inch high-resilience sponge cushions and breathable covers already fitted.

Underneath, it is a rust-resistant steel frame wrapped in all-weather resin wicker, which is the classic poolside build. The woven shell sheds water instead of soaking it, and it will not crack or peel like untreated wicker cane.

The foldable side tabletop is the feature owners mention first. It bolts to either side, so you can put it where your dominant hand reaches. A furniture cover is included, which saves you buying one in the first summer.

At 83 lb for the pair, this is the heaviest set here and one adult cannot easily reposition a single unit. It is also armless, so reading upright still means no forearm support, and the weave can snag where it meets the frame joints under heavy use.

Who this set suits

Readers, nappers and anyone who wants a poolside chair that looks like living-room furniture. It is the most forgiving option for a covered loggia or a sunroom that gets used year-round rather than seasonally.

Because the cushions are removable with breathable covers, they can be washed and replaced independently of the frame, which answers the cost-of-ownership complaint we hear most from pool owners.

Who should skip it

Anyone who moves furniture alone frequently, and anyone on a small deck where 78 inches of length eats the walkway. It is also overkill if you want a chair you can rinse and leave in the rain with no cover step.

If weight is the deciding factor, the Devoko set at position 12 folds flat and one person can carry it easily.

4. SERWALL HDPE Lounge Chair Set with Wheels – Best for Salt-Air Decks

HDPE is the material answer for anyone within sight of the ocean. There is no steel frame here to pit, so salt air simply has nothing to attack. That is why pool owners in coastal areas gravitate to this style and why reviewers single out its corrosion resistance.

At 78.3 inches long, this is one of the longer chairs in the group, which gives tall users room to actually lie out instead of perching. The five-position backrest locks in place rather than sliding, and the whole set is 47.4 lb.

Two details stand out for daily use. The rolling wheels let you drag a chair from a sunny spot to shade without asking for help, and the cup holder is cut wide enough for a tumbler or a stemmed glass rather than just a can.

The genuine drawback is height. This chair sits low to the ground, which feels relaxed while you are lying down and awkward when you need to get up. Reviewers also note the armrests sit roughly 4 inch below the elbow.

Who this set suits

Coastal homes, saltwater pools and anyone who will not have a steel frame anywhere near the water. The long body also makes it a good match for six-foot-plus users who feel cramped on shorter chairs.

If you want the same rust-free body but a higher seat, the Ciokea pair at position 6 has armrests and a 450 lb rating.

Who should skip it

Older adults and anyone with hip or knee trouble. The low seat height is the most repeated complaint in the reviews, and the width and length combination makes replacement cushions hard to source later.

If comfort over time matters more than material purity, plan on adding a cushion, and check the seat dimensions before you buy one.

5. YITAHOME Polypropylene Pool Chaise Set of 2 – Best Budget Pick

The YITAHOME pair is what we recommend when someone wants two working pool loungers without treating it as a major purchase. The body is upgraded polypropylene, the base is wide enough to resist bending, and the rating is 352 lb per chair.

Assembly is the standout detail. One person, no tools, about five minutes per chair, which matters when you are furnishing a deck in one afternoon rather than a weekend.

The rattan-pattern moulding looks better than the price suggests, and the plastic is treated as fade and UV-proof, so it will not grey out after one summer in full sun. Nothing about it will rust, ever, at any humidity.

Where it falls short is comfort and refinement. The slatted seat is rigid, so a cushion is effectively required for anything beyond a short sit, and reviewers note the backrest lever feels light and can flex under heavier users.

Who this set suits

New pool owners filling out a deck on a budget, rental homes, and families who want chairs that survive kids, dogs and squirrels without worry. The plastic surface also shrugs off the spiky damage birds leave on fabric.

Our reclining sectional roundup covers larger multi-seat layouts if your deck is big enough for one.

Who should skip it

Anyone who wants to lie on it bare for hours, since the rigid slats will notice. The 73.6 inch length is also short for tall users, and the flexing back section is not ideal above the stated rating.

Budget for a cushion set on day one. Once padded, this is genuinely hard to argue with for the money.

6. Ciokea HDPE Chaise Lounge Set with Wheels – Best for Heavier Builders

The Ciokea pair solves the two complaints that come up most often with molded resin chairs. It has actual armrests at a usable height, and a 450 lb rating that is 100 lb above every sling chair in this list.

It is also longer than many rivals at 77.76 inches, so taller adults get more room through the shoulder and knees. Five back positions cover sitting, reading and lying flat.

Built-in wheels and a cup holder make daily repositioning painless, and the HDPE is UV-resistant, so it resists fading and cracking in humid or coastal air. Coverage on the seats runs to two years.

Two caveats from reviews. Despite the oversized language in the listing, the seat itself is only 20.5 inches wide, narrower than chairs marketed at the same length. And like all plastic bodies, it heats up in direct sun without a cushion.

Who this set suits

Households with adults over 250 lb, anyone who wants arm support for reading, and buyers who want one person to be able to move a chair without help. It is also a good match for older adults, since the armrests give you something to push off.

The rust-free HDPE build means no coastal restrictions, and the two-year coverage is stated in the listing rather than promised vaguely.

Who should skip it

Anyone who needs a wide, padded seat, since the width is the weak point. It is also not a good choice if you hate assembly, because the time per chair varies a lot.

If you want a cushioned body and a higher capacity, the WAROOM set holds 300 lb with padding. For capacity without armrests, EUNHOO also rates 450 lb.

7. EUNHOO Polypropylene Outdoor Lounger Set of 4 – Best for Big Decks

Four chairs is the configuration nobody else here offers, and for a wide deck or a shared holiday rental it changes the math entirely. Each unit is 20.5 lb, which is the lowest weight of any chair in this group.

Being that light matters more than it sounds. You can carry one to the beach, reposition it for sun, or clear the deck before a storm without recruiting anyone.

The moulding is water-repellent and quick-dry resin, with cutout ventilation through the seat that keeps it cooler than a solid surface in peak summer. The backrest has five positions with a locking mechanism, so it does not creep down while you read.

The 450 lb rating matches the Ciokea for capacity, and the sled base glides rather than digging into grass. The tradeoffs are the same ones every molded chair shares: the slats are hard without a cushion, and there are no armrests.

Who this set suits

Large decks, holiday rental properties and anyone who needs more than two seats. Assembly is quick too, with a single chair taking a few minutes for one person.

If the deck is uneven lawn or a slope rather than concrete, put the SERWALL or Ciokea set higher on your list, since a sled base is steadier on flat paving.

Who should skip it

Anyone who wants a soft, padded seat or arm support. Four hard plastic chairs also reads as a functional set rather than a styled one, so it suits a busy deck more than a resort look.

Buy cushions before the first full day of use. That one addition changes the comfort more than any other part of the chair.

8. Christopher Knight Home Aluminum Mesh Chaise Set – Best Lightweight Option

This is one of the coolest seat surfaces in the group. Mesh is an open weave stretched across the frame, so air passes through it and it never feels as hot as solid plastic or a fabric sling under the same sun.

The aluminum frame is the reason for the long life. Long-term owners report five-plus years of all-weather use on the structure itself, which is the strongest durability evidence anywhere in this roundup.

At 22 lb for two chairs, nothing else here is easier to move. Wheeled head legs let you roll them along a smooth deck, and each chair assembles with eight hex bolts in roughly 15 to 30 minutes.

The honest weakness is the mesh itself. Owners report it tearing after several seasons of sun exposure, and it is not a user-replaceable part, so a torn seat means a new chair. It also runs hot in direct sun until you put a towel or pad on it.

Who this set suits

Hot climates and sun-exposed decks where a solid seat becomes unbearable by noon. The low weight is also a genuine benefit for older adults and anyone who rearranges the deck often.

Those who want the same aluminum frame with a tighter, more supportive sling should choose the Kozyard at position 1 instead, and accept a narrower seat.

Who should skip it

Buyers who want a part they can replace in five years. Mesh failure is the one failure mode here that ends the whole chair, so plan on that cost rather than being surprised by it.

It is also not stackable, which matters if your off-season storage is a garage already full of other things.

9. Aqua Outdoors Water Weighted In-Pool Lounger – Best for Sun Shelves

Everything else in this list is built to keep water away. This pair does the opposite: submerge it and it fills with water, which is what makes it stay put on a sun shelf instead of drifting to the deep end.

That single design decision changes what it is for. A sun shelf becomes a genuine lounging spot where you are waist-deep, shaded by an overhang and out of the wind, rather than a step you perch on for a minute.

The UV16 resin is built for chemical exposure, resisting fading, sagging and cracking from sun, rain and pool chemistry. There is no assembly at all, no screws and no plugs, and the contoured curves support the body properly. Coverage runs five years with US-based support.

The rating of 4.2 is well below the rest of this roundup, and the reason is instructive. Most owners are delighted once they master the filling, and the complaints all point at the same thing: if you do not release trapped air properly, the loungers float or flip.

Who this lounger suits

Pool owners with a tanning ledge or sun shelf, and anyone who wants a seat that is actually in the water. It is optimised for up to 9 inches of depth, and optional risers extend that to 14 inches.

It works on vinyl and fiberglass pools, and because it is resin rather than metal there is nothing to corrode in a saltwater system.

Who should skip it

Anyone without a sun shelf, since a 66 inch frame on a pool deck is shorter than the sling chairs here and wastes the space. It is also a two-person job to fill and lift, given 70 lb per pair.

Take it out of the pool before winter. Optional risers are not offered in every colourway, which is the one detail to check if you plan to extend the depth later.

10. Step2 Vero Pool Lounger – Best for In-Pool and Deck Use

The Step2 Vero is the most flexible in-pool option here because it works in two places. Set it on a shelf in up to 12 inches of water for tanning, or move it onto the deck when you want a conventional poolside seat.

Its weighted cavity is the key feature. You add sand to control how it floats, which is a simpler approach than the Aqua Outdoors water-filling method because you set it once and forget it.

The plastic body is a genuine advantage in two ways. It runs noticeably cooler than a metal frame in direct sun, and the weather-resistant resin holds its colour through intense sun and heavy rain without coating.

The rating of 4.1 is the lowest here, and the cause is specific. A 15 percent one-star share in the reviews is driven largely by sand escaping the weighted cavity within the first year, which slowly destabilises the lounger. Assembly also involves screws drilled through the plastic rather than moulded holes.

Who this lounger suits

Owners with a sun shelf that wants to use the same chair in the water and on the deck, and anyone who prefers set-and-forget sand weighting over careful water filling. The lighter body is easier to move than most in-pool loungers.

Accessory support is worth checking if you plan to read poolside, since the pillow, cup holder and phone holder are all sold separately.

Who should skip it

Anyone whose pool filtration will not tolerate stray sand, since leakage is the dominant complaint. It is also a fixed single recline position with no adjustment, so it is not a reading chair.

If you want adjustable angles in the water and stronger warranty coverage, the Aqua Outdoors pair is the stronger in-water commitment.

11. Asifom 79 Inch PE Rattan Chaise Lounge Set – Best Extra-Long Chair

The Asifom pair is built around one measurement: 78.74 inches. That is the longest body here, and it is the difference between lying flat and lying at an angle for anyone over six feet tall.

The build is PE rattan over a galvanized steel pipe frame with a powder coating and stainless-steel screws. That combination is rust-free for year-round outdoor use, which is the specific construction pool buyers ask about most.

Five back angles cover reading, napping and full flat. The deep, low-slung seating is the most styled of the resin options here, so it reads as a poolside centrepiece rather than deck equipment.

The 79 percent five-star share is the highest in this roundup, but the caveat is consistent. This configuration ships without cushions, and 81.5 lb for the pair means repositioning is a two-person job on a large deck.

Who this set suits

Tall users who have found standard 75 inch chairs cramped, and buyers who want a resort-style silhouette rather than a utilitarian sling. The all-weather rattan build also handles coastal air without corrosion concerns.

It is a good match for a permanent deck installation where the chairs stay in one spot and style matters more than portability.

Who should skip it

Anyone who moves furniture alone, and anyone who wants padding out of the box. You will need to source cushions separately, and matching them to the 78.74 inch length takes some measuring.

If you want cushions included, the WAROOM pair at position 3 is the cushioned alternative with a similar wicker look.

12. Devoko Folding Rattan Chaise Set with Table – Best for Small Patios

The Devoko set is the answer to the most common spatial complaint from pool owners, which is not enough deck. Two cushioned chaises plus a folding side table, and the whole thing folds flat for winter storage.

That fold is the defining feature. A folded chaise carries by one person, stacks against a wall and disappears for the off-season, which none of the full-size resin or HDPE sets here can do.

Underneath, it is a rust-resistant steel frame wrapped in all-weather resin wicker, with thick pads that tie on and can be removed. Being removable and washable is what keeps a cushioned chair alive, and it is why we would rather see this chair survive than a heavier welded one.

Reviewers report two consistent issues. The middle support legs can sit slightly above the deck until weight is applied, which causes a wobble on uneven paving. The folding table is also small and a little unsteady under a full drink.

Who this set suits

Small patios, balconies and pool decks with tight walkways, plus anyone who needs the furniture to disappear in winter. The 1,997-review history also makes it the easiest option here to buy used and still know what you are getting.

It suits rentals and seasonal homes especially well, since the fold is what makes one unit practical to carry between a patio and a garage.

Who should skip it

Older adults, because the low seat height makes rising difficult. It is also not built for harsh multi-season weather without a purchased cover, and the wobble at the mid-leg shows up on anything but flat concrete.

For year-round outdoor durability with no cover step, the HDPE options at positions 4 and 6 are the better long-term commitment.

In-Pool vs. Deck-Side Chaise Lounges: Which One Do You Need?

Most roundups mix these two products together, which is a mistake, because they solve different problems and cannot be swapped. A deck-side chaise lounge is a chair that survives splashes while staying dry. An in-pool lounger is a chair designed to float and stay put in shallow water.

A deck-side lounger needs drainage, a stable ground frame and a backrest that locks at several angles. It is measured in how well it handles being sat on wet, repeatedly, and dragged across concrete. Every chair from position 1 through 8 is built that way.

An in-pool lounger needs weight. Without it, a chair in 9 to 12 inches of water simply drifts to the deepest point of the pool, which is the single complaint that drives the ratings on both in-water picks here. The Aqua Outdoors fills with water and the Step2 Vero takes sand, and those two approaches are the whole difference between a stable lounger and a floating disappointment.

There is a middle path worth considering. The Step2 Vero and the Aqua Outdoors both work outside the pool as well as inside it, so one purchase can cover a sun shelf and the deck beside it. Pure deck-side models are wasted on a shelf, because a 77 inch frame does not fit a 9 inch depth of water.

Our advice is to decide this before you shop, because it narrows the list by half. Shade and water on the sun shelf is an in-pool brief. Long reading sessions on a deck under an umbrella is a deck-side brief. Having both means buying one of each, not choosing one chair to do two jobs.

How to Choose an Outdoor Chaise Lounge for a Pool

Frame material decides survival

Aluminum will not rust, which is why it dominates this roundup. Powder-coated aluminum is the safest general choice for chlorine, saltwater and humid air, and it is light enough for one adult to move. Powder-coated steel is also fine when the coating is intact, but any chip that reaches bare metal becomes a rust stain on travertine or stone decking, which is the outcome pool owners fear most.

Resin wicker over a steel frame is the other durable option. The weave sheds water, and the powder-coated tube underneath handles humidity well. HDPE and polypropylene remove metal from the equation entirely, which makes them the standard coastal choice and the safest option if you refuse to have steel near a travertine deck.

Teak is the one material we would not put on a pool deck. It will not rot, but pool owners consistently describe it as more maintenance than they want, and the hardware eventually streaks the wood. Our outdoor ceiling fan picks cover the other half of a covered deck, where a breeze changes how a lounge feels more than any chair swap does.

Sling seat or cushion: the drying question

A Textilene or mesh sling drains the instant you stand up because there is no foam to soak. That is the single biggest quality-of-life difference on a pool deck. A foam cushion feels better while you are lying on it and holds water, Chlorine residue and sunscreen against the fabric until you rinse it properly.

If you buy cushions, buy quick-dry foam and covers you can remove and wash. The cushioned options here are separable by design, which is exactly the property that keeps a cushioned chair alive instead of turning it into a mildew smell after one forgotten week.

Recline positions and seat height

Five positions is the standard here, and it matters because a chair that only reclines fully flat is not a chair you can read in. The distinction to check is whether the backrest locks. On several chairs the back creeps down while you are reading, which is a small annoyance that becomes a daily one.

Seat height deserves its own paragraph. Molded resin and HDPE chairs in this group sit between 11.4 and 16 inch, while the sling chairs sit higher. A low seat is relaxed when you are lying down and genuinely difficult to rise from if you have hip or knee trouble. If getting up and down is part of your use case, put armrests and height above cushion comfort in your ranking.

Weight capacity and moving one chair alone

Ratings range from 300 to 450 lb here, and the difference matters in homes with adults over 250 lb. The sling-based and wicker chairs in this group rate 300 or 350 lb; the molded resin and HDPE bodies are what reach 450 lb.

Weight cuts the other way too. The lightest set here is 22 lb and the heaviest is 83 lb. If one adult needs to move a chair without help, anything above 60 lb per chair is a genuine problem, and built-in wheels or a fold-flat frame matter more than the number on the spec sheet.

Deck spacing: how much room to leave

Measure before you buy, because a chaise is roughly 78 inches long and 22 to 26 inches wide, and two of them need real linear footage. Leave about 30 inches between adjacent lounges for people to walk past, and 24 inches behind the head end so someone sitting up can lean back without hitting a wall.

On that spacing, a pair of lounges needs roughly 11.5 linear feet of deck. A fourth chair like the EUNHOO set adds about 5.5 feet more, so measure the run before assuming four will fit around a rectangular pool.

Our patio chaise lounge guide goes deeper on how to measure a deck and how recline mechanisms differ between models.

Chlorine pools and saltwater pools are not the same problem

Chlorine attacks fabric and foam, so cushion care and rinsing matter more in a chlorine pool. Saltwater is far less aggressive on fabric but far more aggressive on metal, because salt settles into every joint and screw head and stays there. That is why HDPE and resin in-water loungers are the safest bet on a saltwater system.

Whatever you choose, the rule is the same: rinse with fresh water, not pool water, and let the piece dry fully before covering it. A cover put on over a damp chair holds exactly the moisture that causes mildew and UV damage.

Warranty, parts and the cost of owning it for a decade

Longer coverage is a real differentiator. The in-pool loungers in this roundup carry five-year manufacturer warranties, while most deck-side resin and HDPE options rely on the retailer’s return window alone. Read the warranty length before you buy, not after.

Then think about parts. A chair whose cushion can be washed and replaced will outlast one whose only part is the whole seat. When we compare a premium all-weather chair against a budget one over ten years, the cushion replacement cost usually decides the tie more than the original purchase does. Buy the frame you want to keep for a decade and accept that the pad is a consumable.

Who should buy what, in one line each

Aluminum and sling for chlorine decks, a saltwater pool or a rental where someone will move the chairs. Resin wicker with removable cushions when comfort and styling come first and the furniture stays put. HDPE or polypropylene for coastal air, heavier adults and anyone who wants no metal on a stone deck. In-pool resin, water or sand weighted, if you have a sun shelf. Folding rattan if deck space and off-season storage are your binding constraints.

Caring for Pool Chaise Lounges Through the Season

Every chair here survives longer with the same basic routine. Rinse with a garden hose using fresh water after swimming, and pay attention to the frame joints and the hardware, which is where salt and chlorine concentrate.

Wash cushions separately with mild soap and a soft brush, and let them dry completely in the air before they go back on. Standing moisture under a cushion is what turns a good chair into a mildew problem.

Cover the furniture when it is not in use, and never cover a wet chair. For resin wicker and HDPE, an annual rinse and a quick check for loose screws covers the whole maintenance requirement.

Before winter, dry everything, apply a light coat of protective spray to metal frames, and store folding or stackable chairs indoors if you can. In-pool loungers should come out of the water for the off-season so the resin is not sitting in water through freeze-thaw cycles.

Frequently Asked Questions

The Best Outdoor Chaise Lounges for Pools in 2026

After putting all 12 through the same five criteria, the Kozyard aluminum Textilene chaise stays the best outdoor chaise lounge for pools because it combines a rust-free frame, a draining seat and a weight one adult can manage. The Crestlive pair covers the value slot at 28 lb for two chairs, the WAROOM set covers comfort with real foam, and the Aqua Outdoors and Step2 picks are the two that work with you in the water as well as beside it.

Match the build to your environment rather than to the look. Aluminum or HDPE for salt and humidity, resin wicker with removable cushions if comfort leads, molded resin if you need 450 lb, and a weighted in-pool lounger if you have a sun shelf. Whatever you choose, budget for a cushion on the rigid models and rinse everything with fresh water.

Measure your deck before you order. Roughly 11.5 linear feet fits a pair with proper walkways, and getting that wrong is the most common regret new pool owners report.